in

How A Braking System Of Car Works ?

How A Braking System Of Car Works

Introduction of braking system of car :

The braking system of car is one of the most significant systems of a vehicle. It has the following basic roles.

1. It should slow a moving vehicle.

2. It should bring a vehicle to a stop.

3. It needs to hold a vehicle stationary when stopped.

4. It permits directional control during maximum braking.

In a vehicle if the braking system does not operate properly the driver and passengers could face an accident. Professionals who service the brake system must be highly skilled experts because the work they do save lives.

During the design stage, if all of the various dynamics are not considered most braking systems will result in improper braking. When the braking system is not functioning correctly it will be up to the driver to compensate risk. In many cases, the response of the human is either too slow or too quick to react to a braking state. In both cases, there is chance for loss of vehicle control.

Braking System Overview

The complete brake system contains of the major components shown in Figure. The complete brake system can be divided into

  • The service brakes slow and stop the moving vehicle.
  • The parking brakes hold the vehicle stationary.
  • The anti-lock braking system (ABS) is a another major subsystem.

Many cars now also include traction control as part of the braking system functions. Braking action on an automobile press with the driver’s foot on the brake pedal. The driver steps the pedal and the pedal transfers that force to the master cylinder pistons. The brake pedal also increases the force of the driver’s foot through lever. The brake pedal is mounted on a lever with a pivot near the top of the lever.

The movement of the pedal causes a push-rod to move against a master cylinder. The master cylinder is mounted inside the engine compartment on the rear bulkhead. The master cylinder is a hydraulic pump that is operated by the driver through the brake pedal. Most brake pedal installations are an example of what is called a second class lever. A second class lever has a pivot point (or fulcrum) at one end and force applied to the other end.

A second class lever transmits the output force in the same direction as the input force, and multiplies the input force, based on where the output load is placed. The brake pedal has a 10-inch lever, and the load is 50.8 mm from the fulcrum (203mm appxox from the pedal). The pedal ratio, or the force multiplying factor, is the length of the lever divided by the distance of the load from the fulcrum.

Types of  braking system

01 - types of braking system in automobile - different types of automobile braking system

History of Braking system:

01 - BRAKE SYSTEM OF A CART WAGON - COMPONENTS OF BRAKE SYSTEM IN A WAGON CARTModern automobile brakes evolved from the comparatively crude brakes of cart. The earliest automobile brakes were pads or blocks applied by levers and linkage to surface of a solid tyre on a wooden-spoke wheel. A similar principle of leverage that employment in popular foot lever installations inflated the force of the brake pad applied to the solid tire.

These brakes worked well with speeds of 10 mph to 20 mph and minute traffic. Higher performance and gas tires meant that early wagon brakes were temporary on cars. By the tip of the primary decade of the 20th century, cars were exploitation either external contracting band brakes or internal expanding drum brakes. A number of internal increasing band brakes were tried on some early cars.

External contracting brakes have a band lined with friction material wrapped around a drum situated on the driveline or on the wheels. The band is anchored at one finish or at the center; levers and linkage tighten the band round the drum for braking force. Servo action on associate external band brake tends to form the brake grab at high brake forces and high drum speed.

Different issues related to band brakes enclosed dirt and water harm and loss of friction with external bands and therefore the tendency of those brakes to lock if the drum hot and expanded an excessive amount of. Internal band brakes conjointly damaged from band and drum heating and reduced braking force .As drum brakes evolved, internal-expanding shoe-and-drum brakes became the quality.

What do you think?

0 points
Upvote Downvote

Total votes: 0

Upvotes: 0

Upvotes percentage: 0.000000%

Downvotes: 0

Downvotes percentage: 0.000000%

Written by Engineeringlover

Engineeringlover

Hey , Welcome to my Engineering & Technology based Website . I am Sunny from New Delhi (India), Mechanical Engineer by Profession & Blogger by Passion. I started Engineering Lover as a passion, and now it’s empowering more than 100,000+ readers globally.

Comments

Leave a Reply

Loading…

What Is Multi Plate Clutch Their Working & Construction

Why Lubrication Is So Important & Properties Of Lubricants